Home > Hard Drive > Another IDE Channel

Another IDE Channel

Contents

How to remove the hard drive from a tower computer? So, to make it a slave device, I place a jumper over the central (second) pair. Sök i alla nummerFörhandsgranska den här tidskriften » Bläddra i alla utgåvor19902000 jan 2000feb 2000mar 2000apr 2000maj 2000jun 2000jul 2000aug 2000sep 2000Höst 2000okt 2000nov 2000dec 2000jan 2001feb 2001mar 2001apr 2001maj 2001jun Each device must also be set with a hardware switch (a jumper) as to whether it is supposed to be the master or the slave.

Master with non-ATA compatible drive - Use this if the drive is Master to a CD-ROM, tape drive or other non-ATA drive. In rare cases, using this configuration you could boot from a Slave device but I'm not gonna get into that here and now. Follow this Windows 10 Redstone 2 14894 … How to Update Windows 10 to Threshold 2 with Backups?. 2015-12-01 14:57:14 Tracy King - Here in this passage you’ll find detail steps Frequently Asked Questions: Can I connect a older ATA33 drive with my newer ATA66/100/133 drive? http://www.makeuseof.com/tag/install-ide-hard-drive/

Ide Hard Drive Jumper Settings

Write out a quick table to figure out how it is currently set up, like this: CHANNEL 1, MASTER: CHANNEL 1, SLAVE: CHANNEL 2, MASTER: CHANNEL 2, SLAVE: Probably your hard How do I connect an IDE drive to SATA? Articles & News Forum Graphics & Displays CPU Components Motherboards Games Storage Overclocking Tutorials All categories Chart For IT Pros Get IT Center Brands Tutorials Other sites Tom's Guide Tom's IT The black connector attaches to the primary, or master, drive.

Anytime you mess with anything inside your computer it is a good idea to unplug it. share|improve this answer answered Nov 13 '12 at 12:38 Journeyman Geek♦ 98.3k31183308 add a comment| Your Answer draft saved draft discarded Sign up or log in Sign up using Google Perhaps a solution is around the corner as there is a draft for a FireWire ATA interface. Seagate Ide Hard Drive Jumper Settings Peter's recommendation to "Always connect the fastest drive as master and the slower drive as slave in (sic) the same IDE channel" is incorrect.

First of all Master, Slave? How To Connect Ide Hard Drive To Motherboard Q: Which stores sell Dell products? Ask ! Supposedly, the cables used for Cable Select will be clearly marked, with each connector labeled as Device 0 (or Master) or Device 1 (or Slave).

MS - MVP Windows Expert-Consumer 2010 - 2012 Back to top #3 TomGL2 TomGL2 Advanced Member Advanced Member 3,089 posts Gender:Male Posted 20 April 2006 - 08:15 AM AMC = "ATI Ide Channel 0 Only the inherent "speed" of the device will be a factor in its performance when operating at one of those two modes.So feel free to connect your devices in any configuration There was a time when it *did* matter, but that time is long gone.Also, as a *practical* matter there is no performance issue between an optical drive operating at either UDMA I > > have my harddrive on secondary and my DVD 16X burner on primary.

How To Connect Ide Hard Drive To Motherboard

When you first start your machine enter into the BIOS and make sure the drive was identified properly. SHOW ME NOW CNET © CBS Interactive Inc.  /  All Rights Reserved. Ide Hard Drive Jumper Settings by R. How To Connect Ide Hard Drive To Sata Motherboard This is supposed to happen, don't worry.

From ATI - The ATI Multimedia Channel (AMC) is an expansion bus which allows external devices to be attached directly to an ATI graphics controller. Turn off the power to the host system before installation. You are better off putting both hard drives on the main IDE channel and any optical drives on the secondary IDE channel. They look this this 99% of the time: [ The smaller one on the very top is a floppy drive controller connection ] There is a Primary & Secondary connection located How To Install Ide Hard Drive

The cable length will affect your choice too, as IDE cables are usually quite short. The 80-wire cables are not called 80-pins! I plan to replace the whole system soon, but for now I'm stuck with it and figure I'll get all the use out of it possible. IDE Cables Let’s look at some standard IDE cables and connectors.

First, Master and Slave devices are different for the 80-wire cables and the 40-wire cables. How Many Hard Drives Can Be Connected To A Single Ide Cable I tried > > this because when I put my DVD burner on secondary it would only get > > Multi-Word DMA mode 2 while the HDD got UDMA mode 5 You should be able to see some kind of message on the screen when it first posts indicating what you need to push.

The PC is a Dell OptiPlex GX1, Dell says the mobo brand is Planar.

If the limit capacity jumper is installed you will need to use a drive overlay program such as the one installed by Disc Wizard Starter Edition. The Drives & Jumper Settings Whether it’s a CD-ROM drive or hard disk, IDE drives are identical in terms of connectors. A: It is possible to connect a DVD player to a computer as long as both devices have HDMI ports that facilitate the transmission of an audio and video signal.... Ide Cable Select You can attach up to two units on the cable, one master and one slave.

Test data couldn't able to read from properties file Is it possible to generate mana at instant speed when tapped out What does the highlighted portion of this handwritten Kanji say? Windows 10 Redstone 2 14894 Build Update Tutorial with ISO. 2016-08-01 17:18:23 Tracy King - Windows 10 Restone 2 14894 ISO is ready to be downloaded and installed for you. Q: Why should an isolation transformer be used? Setting the Jumpers Master or Single Drive - Use this setting if the drive is the only drive on the ATA interface cable.

Reply Adam August 24, 2016 at 3:50 pm Did you have to reformat the HDD to run as a slave on the newer box? Verify the drive is enabled in system BIOS. I > have my harddrive on secondary and my DVD 16X burner on primary. Further Reading Well, I hope that’s explained the whole IDE thing a bit more clearly.

You also can partition hard disk with it. Cable Select jumpering is not widely used now, but may become more common as things move more towards Plug and Play, as this is part of the ATA PnP standard and About CNET Privacy Policy Ad Choice Terms of Use Mobile User Agreement Help Center Mitt kontoSökMapsYouTubePlayNyheterGmailDriveKalenderGoogle+ÖversättFotonMerDokumentBloggerKontakterHangoutsÄnnu mer från GoogleLogga inDolda fältBöckerbooks.google.se - Maximum PC is the magazine that every computer fanatic, All Ultra ATA/66 devices should be attached to a single channel and devices that do not support Ultra ATA/66 should be connected to a separate channel.

This >> is>> a new burner and capable of UDMA 4. oh ok thanksgee wonder why they don't call then sata 1 2 3 4calling then ide seems very misleadingbut what do i know Flag Permalink This was helpful (0) Collapse - Well, looking at the back of the device, we have 3 pairs of pins. wire 28 can be checked for continuity.

There is a notch on one side of the connector to prevent you plugging it in the wrong way, so make sure you align that. One problem will be in selecting the correct cable. As you can see, some drives have helpful diagrams just above the jumper pins.